How-to
How to read the live map
The live map packs a lot into small symbols. This page explains each of them: what the shape of a marker tells you, what its colour and brightness mean, how to read a track, and how to narrow thousands of vessels down to the ones you want.
Last reviewed
Markers: dots and arrows
Every marker is one vessel at the last position we received for it.
Zoomed far out — below zoom level 5, where an ocean or a continent fills the screen — every vessel is a small dot in its ship-type colour, whether it is moving or not. At that scale an arrow would be a few pixels long and its direction impossible to read, while thousands of dots show where the shipping lanes run. The dots are slightly see-through, so a lane that looks more solid has more ships in it.
From zoom level 5, about the scale of a sea or a stretch of coast, the shape tells you whether the vessel is moving.
Arrow. Moving at 0.5 knots or more. Points along the heading, or the course over ground if no heading is sent.
Dot. Under 0.5 knots, or reporting “moored” or “at anchor”, or sending neither heading nor course.
Faded. Last heard more than an hour ago. The marker is where the vessel was, not where it is.
Faint. Last heard more than 24 hours ago. Normally seen only while the data feed itself is offline and the whole map is a last-known picture.
Ringed. A vessel in your fleet. Shown when you are signed in.
Larger, outlined. The vessel you have selected. Its name is shown at every zoom level while vessel names are switched on.
An arrow points where the ship’s bow points — its heading. That is not always the direction it is travelling: a ship crabbing across a strong tide is drawn at an angle to its own track. If a vessel sends no heading, the arrow uses the course over ground instead.
A dot means stopped, or as good as: slower than 0.5 knots, or reporting a status of moored or at anchor. A vessel that reports “moored” while plainly moving still gets a dot, because the dot follows the reported status; open the vessel and the panel will tell you its actual speed.
Markers shrink as you zoom out so that a busy strait reads as a pattern of traffic rather than a solid blob. Vessel names appear beside markers from zoom level 9, roughly the scale of a single port approach.
Colours: ship type
Colour shows the kind of ship, taken from the two-digit ship type code it broadcasts. The map groups the hundred possible codes into 15 colours:
| Colour and category | AIS ship-type codes |
|---|---|
| Cargo | 70–79 |
| Tanker | 80–89 |
| Passenger | 60–69 |
| Fishing | 30 |
| Tug | 52 |
| Towing | 31–32 |
| Sailing | 36 |
| Pleasure craft | 37 |
| High-speed craft | 40–49 |
| Military | 35 |
| Pilot vessel | 50 |
| Search & rescue | 51 |
| Dredging | 33 |
| Diving ops | 34 |
| Other / unknown | 0–29, 38–39, 53–59, 90–99 |
The same list is in the map’s Legend (bottom left), with a count of how many vessels of each kind are on screen. What each individual code means is in AIS ship types explained.
Faded markers, the feed indicator and the count
A position is only as good as it is recent, so the map shows age in two ways.
Per vessel: a marker fades once its position is more than an hour old. The vessel has usually sailed out of range of the shore receivers (see who hears it), and the marker is where it was, not where it is. Vessels not heard for 24 hours drop off the map altogether.
For the whole map: the indicator in the top bar reads Live with a green dot when positions are arriving, followed by the number of vessels in view. If no position from any vessel has reached us for 30 minutes it changes to Feed offline in amber, and a banner states the time of the last position received. The map then shows every vessel where it was last heard and corrects itself when the feed returns.
Showing N of M. The map loads up to 50,000 vessels at a time (fewer on phones). When more than that match — typically on the world view with no filters — the indicator says so, for example Showing 48,211 of 61,234 — zoom in for all: 61,234 vessels match your filters and were heard in the last 24 hours, and the map has drawn 48,211 of them. The ones left out are not simply the oldest. Quiet waters keep their ships and only the busiest areas are thinned, so the lanes keep their shape; the same ships stay on screen from one refresh to the next, and zooming in only adds ships. The map then asks for the area you are looking at, so zoom in until the message goes and you have every matching vessel there. Vessels in your fleet are drawn even where an area is thinned, as long as no filter is set.
When the map first opens it may show a quick first picture and the words loading more; the rest of the vessels fill in a moment later without anything moving.
Selecting a vessel
Click or tap a marker to open the vessel panel. It shows the name, flag, type and a photo where a freely licensed one exists, then the current speed, course, status, destination and ETA, and how long ago the position was received. From the panel you can add the vessel to your fleet, set alerts on it, copy a link to it, or open its full vessel page with identity details and history.
The selected vessel is drawn larger with an outline, and its track appears on the map.
Tracks
- Stopped
- Under 5 kn
- 5–10 kn
- 10–15 kn
- 15–20 kn
- Over 20 kn
- Gap or position jump
- Colour is speed, from grey for stopped through to red for more than 20 knots. A ship slowing for a pilot station or speeding up clear of a harbour shows as a change of colour.
- Dashed means unknown. Where two consecutive positions are more than 30 minutes apart, the map joins them with a dashed straight line rather than pretending to know the route. The same is done for a jump that would have needed more than 60 knots — usually two vessels sharing one identity, or a bad position.
- Small chevrons along the line show the direction of travel, and a ring marks where the track starts.
- Time ticks are labelled in UTC, with a trailing Z:
14:00Z. Zoomed out you see one tick a day; zooming in adds six-hourly, hourly and then 15-minute ticks.
Track points are stored at most once every five minutes per vessel, so a track is a faithful outline rather than a second-by-second record: a tight turn inside a harbour will look more angular than it was.
The range buttons choose how far back to look: the last 24 hours for everyone, and longer ranges with Pro, up to the 30 days we keep. Press play to replay the track — the whole period runs in about a minute, and the speed buttons make it faster — or drag the slider to a moment. Pro can also export the track as CSV, GeoJSON, GPX or KML.
Layers
The Layers button changes what is drawn under and around the vessels.
- Base map: Standard or Satellite. Standard is a plain chart-like map. Satellite is a cloud-free mosaic of imagery from 2016 and 2017 — useful for seeing berths and breakwaters, but it is a picture of the coast, not a current photograph. You will not find today’s ships in it.
- Vessel names. On by default; shown once you have zoomed in.
- Ports. Small dots from zoom level 4.5, anchor badges from zoom level 7. Click one for a card that links to its port page and can filter the map to vessels bound there.
- Sea marks. Buoys, lights and harbour detail from OpenSeaMap, drawn over the base map. They appear from zoom level 9; further out there is nothing to show.
- My alert areas. The alert areas you have drawn, with Pro.
Your layer choices are remembered on the device you set them on.
Search and filters
The search box finds vessels by name, call sign, IMO number or MMSI, and ports by name or code, once you have typed 2 characters. Choosing a vessel flies the map to it and opens its panel; choosing a port flies to the port. Names are matched as broadcast, so a ship that has been renamed is found under the name it is transmitting now. The IMO number is the search that survives a renaming.
The Filters panel narrows the map. Each filter you set becomes a chip you can remove:
- Ship type — the colour categories above.
- Status — under way, at anchor, moored, fishing, restricted and aground, from the navigational status the crew have set.
- Speed — presets (stopped, under 5 kn, 5–15 kn and over 15 kn) or your own range in knots.
- Destination — a port, matched by its code, or any text the crew typed. Port matching is best-effort; this guide explains why.
- Flag — the country of registry, derived from the MMSI.
- Last position report — only vessels heard in the last 15 min, 1 hour or 6 hours. The quickest way to hide last-known markers and see only what is being received now.
- Named vessels only — hides vessels whose name has not been received.
Replaying the past
The Replay button in the top bar turns the map into a view of the past. A timeline appears at the bottom of the map and a Replay badge at the top says which moment you are looking at, in your own time zone (hover it for UTC). Press play to watch every vessel in view move, drag the timeline to a moment, or step one snapshot at a time; Back to live or Escape returns to the live map. Your filters and alert areas apply as they do live, and clicking a vessel shows its position, speed, course and status at that moment.
Replay is built from snapshots: every 15 minutes we record every vessel our receivers heard in the hour before, and older snapshots are thinned — every 15 min for the last 30 days, then hourly, then every 6 h. Between two snapshots the map moves each vessel in a straight line from one report to the next; paused, it shows one snapshot exactly. The shaded line on the timeline is the number of vessels in each snapshot. Hatched stretches are gaps: our receiver feed was down and nothing was recorded, so playback skips them and says so. The archive starts from when recording began, so at first it does not reach far back.
Everyone can replay the last 3 hours. Further back the timeline is shown with a lock: replaying the whole archive is part of Pro. As live, replay shows terrestrial AIS from Class A transponders only.
Sources
Statements about AIS and maritime standards on this page were checked against the following. Statements about what VesselTrack does describe the software as it runs today.
- OpenFreeMapThe standard base map: vector tiles built from OpenStreetMap data.
- EOX — Sentinel-2 cloudlessThe satellite base layer: a cloud-free mosaic of 2016 and 2017 imagery. It is a picture of the coast, not a live view.
- OpenSeaMapThe sea marks layer: buoys, lights and harbour detail.
- US Coast Guard Navigation Center — Class A AIS position report and static/voyage dataField-by-field contents of AIS messages 1, 2, 3 and 5, reproduced from Recommendation ITU-R M.1371-5: navigational status codes, ship-type codes, “not available” values.
Found a mistake? Email support@vesseltrack.net or see how to contact us. Corrections are made on this page and the review date is updated.