Explainer

AIS Class A vs Class B: what the difference means on a tracker

AIS comes in two shipborne grades. Class A is the full specification that commercial shipping must fit; Class B is a cheaper, lower-powered set that most yachts and small working boats use. They share the same radio channels and can see each other, but a Class B vessel reports less often, from less power, and leaves out most of what a tracker shows about a voyage. Here is the difference, field by field, and how to spot it.

Last reviewed

Who fits which class

Class A is what the carriage rules require. Under regulation V/19 of the SOLAS convention, AIS must be fitted on every ship of 300 gross tonnage and upwards on international voyages, on cargo ships of 500 gross tonnage and upwards that stay in domestic trade, and on all passenger ships whatever their size. Those ships fit Class A because it is the equipment built to the performance standards the International Maritime Organization adopted.

The same IMO guidelines point out who is outside the rule: warships, naval auxiliaries and other government-operated ships are not required to fit AIS, and small vessels such as leisure craft and fishing boats may be exempt. Many countries add their own rules for vessels in their waters, which is why some fishing boats, tugs and ferries below the SOLAS thresholds carry AIS too — some of them Class A, many of them Class B.

Class B is the voluntary option: interoperable with every other AIS station, but not built to the full IMO standard. The US Coast Guard’s comparison, last revised in February 2020, put a Class A set at roughly US$750 to US$3,500 and a Class B set at roughly US$500 to US$1,600, which is the main reason Class B exists.

The messages each class sends

Everything in AIS travels as numbered messages defined in Recommendation ITU-R M.1371. The two classes use different numbers for the same job, which is how receiving equipment knows which kind of set is talking:

MessageNameSent by
1, 2, 3Position reportPosition, speed and course over ground, heading, rate of turn, navigational status, position-accuracy and RAIM flags.Class A
5Static and voyage related dataIMO number, call sign, name, ship type, dimensions, draught, destination, ETA, type of position-fixing device.Class A
18Standard Class B position reportPosition, speed and course over ground, heading, position-accuracy and RAIM flags, and whether the unit is “CS” or “SO”. No rate of turn or navigational status.Class B
19Extended Class B position reportA position report with name, type and dimensions attached. The US Coast Guard lists it as no longer required.Older Class B
24 (parts A and B)Static data reportPart A: the name. Part B: ship type, call sign, dimensions and the maker’s vendor ID. No IMO number and nothing about the voyage.Class B
27Long-range position reportA short position report meant for reception far outside the range of shore stations, typically by satellite.Class A and Class B “SO”

A Class A position report is a full position report; its static and voyage data arrive separately in message 5. A Class B set sends message 18 for its position and splits its identity over the two halves of message 24, sent within a minute of each other. A receiver can catch one half and miss the other, so a Class B vessel can be on a map with a name but no type, or the other way round, until both halves have been heard.

Two kinds of Class B: CS and SO

AIS stations share two VHF channels by dividing every minute into 2,250 time slots, each long enough for one position report. How a set claims its slots is the real technical difference between the classes:

  • Class A uses SOTDMA, self-organising time-division multiple access: each station announces which slots it will use next, so the stations around it plan around those slots and reports go out on schedule.
  • Class B “SO” uses the same self-organising scheme. It transmits at 5 watts and reports faster at speed, so it behaves much like a scaled-down Class A.
  • Class B “CS” uses CSTDMA, carrier-sense access: it listens to a slot and transmits only if the slot is free. It transmits at 2 watts, and its schedule is kept “subject to slot availability” — in crowded waters a CS unit gives way to the others, so its reports can be later or rarer than planned.

The US Coast Guard sums it up as “Class B/SO is generally more capable; Class B/CS is generally less expensive”. Every message 18 carries a flag saying which kind of unit sent it.

How often each class reports

A Class A ship reports every 2 to 10 seconds when moving, faster the quicker she goes and while she is altering course, and every 3 minutes at anchor or moored. The full Class A schedule is in the guide to how AIS works. Class B is slower:

SpeedClass AClass B “SO”Class B “CS”
2 knots or less3 min at anchor or moored; otherwise 10 s3 min3 min
2 to 14 knots10 s30 s30 s
14 to 23 knots6 s15 s30 s
Over 23 knots2 s5 s30 s

Both classes send their identity every 6 minutes. In distance rather than time, the gap is easier to picture. At 20 knots a ship covers about 61.7 metres between Class A reports, 154.3 metres between Class B “SO” reports and 308.7 metres between Class B “CS” reports.

Class A: 11 reports in the minute, every 6 s, about 61.7 metres apart. Class B “SO”: 5 reports in the minute, every 15 s, about 154.3 metres apart. Class B “CS”: 3 reports in the minute, every 30 s, when a slot is free, about 308.7 metres apart.Class A61.7 m apartClass B “SO”154.3 m apartClass B “CS”308.7 m apart0 s15 s30 s45 s60 s
One minute of position reports from a vessel making 20 knots, by class of transponder. Each dot is a report. Intervals from the US Coast Guard Navigation Center’s class comparison.

Power matters as much as frequency. At 2 watts, and usually from a low antenna on a small boat, a Class B “CS” set is heard over a much shorter distance than a 12.5-watt Class A set on a ship’s mast. The same shore receiver that follows a cargo ship well out to sea may only pick up a yacht near the harbour mouth.

What a Class B vessel cannot tell you

The US Coast Guard’s description is precise: Class B sets report the vessel’s static data every 6 minutes “but, not any voyage related information”. Side by side:

FieldClass AClass B
IMO numberSent every 6 minutesNot in any Class B message
Destination and ETATyped in by the crew, sent every 6 minutesNot sent
DraughtTyped in by the crew, sent every 6 minutesNot sent
Navigational statusWith every position reportNot sent
Rate of turnWith every position report, if a sensor is connectedNot sent
Name, call sign, type, dimensionsEvery 6 minutesEvery 6 minutes

The consequences on any tracker follow directly. A Class B vessel has no destination and no ETA, so it never appears in a port’s list of expected arrivals. It has no IMO number, so it can only be followed by its MMSI and name. And it has no navigational status: it cannot say it is at anchor or moored, so anything that depends on the status — a status pill, an alert that fires when a vessel reports itself moored — has nothing to work with. Whether it is stopped has to be read from its speed.

How to tell which class a vessel uses

Receiving equipment knows from the message number. A tracker that shows the message type, or labels the class, settles it; otherwise the pattern of what is and is not reported gives it away:

  1. No IMO number, destination, ETA or draught, ever. A Class A ship can leave the voyage fields blank, but a vessel that has never sent any of them, over days, is very likely Class B.
  2. No navigational status. A Class A set always sends one, even if it is the code for “not defined”. A vessel page that shows the status as not reported, on every visit, points to Class B.
  3. The kind of vessel. A sailing yacht, a small fishing boat or a pleasure craft with a ship type of 36 or 37 (see AIS ship types) is usually Class B; a cargo ship, tanker or cruise ship is Class A by law.
  4. A sparse track. Positions every 30 seconds instead of every few seconds. This is only visible where a tracker keeps every report; a tracker that thins its tracks (this one stores at most one point every five minutes) hides the difference.

What this means on a tracker

Whether you see Class B vessels at all depends on what a tracker collects and how close its receivers are to where small craft sail. Some services take only the Class A messages; some take both. Even a tracker that takes both will show fewer Class B vessels than are out there, because their lower power and lower antennas shorten the distance at which they are heard.

VesselTrack shows both: we receive Class A and Class B transponders as relayed by the shore receivers in our feed, so the map and vessel pages include small craft whenever a receiver hears them — less reliably, and with less detail, than ships with Class A sets, and never the many small boats that carry no AIS at all. The details of what we receive, and from where, are in what VesselTrack receives. Whatever a vessel sends, the vessel pages here show each missing field as “not reported” rather than guessing, so a Class B vessel’s page will be shorter, not wrong.

If you are choosing a transponder for your own boat, the trade-off is the one above: a Class B “CS” set is the cheapest way to be seen, a Class B “SO” set reports more often and more strongly, and a Class A set is what you need if the rules require one. Check with your flag administration before buying; the carriage rules for smaller vessels are national.

Related: why a ship disappears from AIS and how accurate AIS positions are.

Sources

Statements about AIS and maritime standards on this page were checked against the following. Statements about what VesselTrack does describe the software as it runs today.

Found a mistake? Email support@vesseltrack.net or see how to contact us. Corrections are made on this page and the review date is updated.