Explainer

Why a ship disappears from AIS, and how to tell why

A ship you were following stops moving on the map, its marker fades, and nothing new arrives. Usually nothing is wrong: it has sailed beyond the reach of the receivers that hear it. Sometimes the transponder has been switched off, has failed, or has started broadcasting under a different number. This guide explains each reason, when ships are allowed to switch AIS off, and how to work out which one you are looking at.

Last reviewed

The usual reason: out of range

AIS is VHF radio. It carries roughly as far as an antenna can see over the curve of the Earth, which is why the International Maritime Organization’s guidelines give “a typical value to be expected at sea” of 20 to 30 nautical miles, depending on antenna height. A tracker fed by shore stations — terrestrial AIS — hears a ship only while she is within that kind of distance of one of its receivers.

So a ship leaving a port is followed in detail as she clears the coast, then, a few hours later, nothing more arrives. She has not vanished; she has sailed out of earshot. The tracker keeps showing her last-known position, which grows older until she comes back within range of a receiver on the far side — days later after an ocean crossing. On this site a marker fades once its position is more than an hour old, so you can see at a glance that it is no longer current.

Coasts are not covered evenly either. Receivers are put up by volunteers, port authorities and companies where they find it useful, so busy ports and straits are often heard by several stations while long stretches of remote coastline are heard by none. A ship can go quiet a few miles offshore of a coast that simply has no receiver.

To put a number on it: of the 34,335 vessels we heard in the 24 hours to , 8,710 (25%) had not been heard for more than 6 hours by the end of that period. The figure says how ordinary silence is, not why: it counts ships that sailed out of receiver range and ships lying where no receiver hears them alongside any that switched off.

The guide to how AIS works has a diagram of how reception works and the other ways a position can be late or wrong.

Can a ship turn off its AIS?

A ship that is required to carry AIS is required to keep it on. The SOLAS rule says ships fitted with AIS “shall maintain AIS in operation at all times except where international agreements, rules or standards provide for the protection of navigational information”. The IMO’s guidelines for using AIS on board, Resolution A.1106(29), spell out the exception in paragraph 22:

“AIS should always be in operation when ships are underway or at anchor. If the master believes that the continual operation of AIS might compromise the safety or security of his/her ship or where security incidents are imminent, the AIS may be switched off.”

The same paragraph attaches conditions:

  • the switch-off and the reason for it are recorded in the ship’s logbook;
  • if the ship is in a mandatory ship reporting system, the master reports it and the reason to the competent authority, unless doing so would itself compromise safety or security;
  • the master restarts AIS “as soon as the source of danger has disappeared”;
  • after power is restored the set starts transmitting again after a two-minute initialisation.

The case usually given is a ship crossing waters with a piracy threat, where broadcasting her position could help an attacker find her. National rules can be stricter in their own waters: in the United States, for example, the Coast Guard requires AIS to be on whenever the vessel is under way or at anchor, and at least 15 minutes before unmooring, and requires a switch-off to be reported to the nearest Captain of the Port or Vessel Traffic Center.

Some ships never had to switch it on. The IMO guidelines note that warships, naval auxiliaries and other government-operated ships are not required to fit AIS, and that leisure craft, fishing boats and some other small vessels may be exempt. A naval ship that is not on the map is not missing; it is not transmitting, by design.

Powered down, laid up or broken

Ports set their own rules: the IMO guidelines say only that “in ports AIS operation should be in accordance with port requirements”. Many ships stay on the air alongside, reporting every three minutes with the status moored. Others shut down — a ship in dry dock, laid up for months, or with her electrical plant off for maintenance sends nothing, and her page shows the position where she was last heard, often in or just outside the port.

Equipment fails too, and the failures look like silence:

  • No position fix. AIS takes its position from the ship’s satellite-navigation receiver. If that fails, a Class A set sends the “not available” position, which a tracker cannot plot. The US Coast Guard has documented older units that stopped producing valid position reports altogether after a change to the GPS constellation. Class B “CS” units do not transmit at all without position information.
  • Antenna, cable or power faults. A damaged VHF antenna or cable can cut the range sharply, so a ship is heard only when she passes close to a receiver, or not at all.
  • Static data only. A set can keep sending its name and voyage data while its position reports are missing, so a tracker learns that the ship exists without being able to place her.

A new or wrong MMSI

A tracker knows a ship only by the MMSI in her messages. When a ship is sold and re-registered under another flag she normally gets a new MMSI. To a tracker, the old number goes silent and a new one appears — often with the same name. The page you were watching has gone quiet while the ship sails on.

The cure is the IMO number, which stays with the hull for life. Search for it with the map’s search box or the IMO number lookup; if the ship is broadcasting under a new MMSI with her IMO number set, she turns up under both. VesselTrack addresses vessel pages by IMO number where there is one for exactly this reason (see IMO numbers).

The opposite problem looks like disappearance too. The US Coast Guard reports transponders programmed with numbers such as 111111111 or 123456789; two vessels sending the same MMSI “will appear as one vessel (jumping from position-to-position or line-to-line)”. The ship you are following may be fine while her page shows another vessel’s positions.

Going dark on purpose, and spoofing

Some ships switch AIS off without a safety reason: to fish where they are not licensed, to hide a ship-to-ship transfer, or to keep a good fishing ground from competitors. This is what “dark ships” and going dark usually refer to in the news. It is real but it is not common, and it is hard to prove from a shore-based feed, where an ordinary gap in coverage looks the same.

The best public measurement comes from a study by Global Fishing Watch and university researchers, published in Science Advances in 2022, which found more than 55,000 suspected intentional disabling events by fishing vessels between 2017 and 2019 — after first separating deliberate gaps from gaps in reception. They clustered near the edges of countries’ exclusive economic zones and in areas where catches are transferred between ships. The researchers also note the legitimate reason: protection from piracy. That work needed years of data and a careful separation of deliberate gaps from gaps in reception; a single silent ship on a coastal tracker tells you much less.

Spoofing is the other deliberate interference. A ship can broadcast a false position, or someone can transmit AIS messages for a ship that is not there. Separately, jamming and spoofing of satellite navigation — which the ITU, ICAO and IMO jointly warned about in March 2025 — can make a ship’s own receiver calculate the wrong position, which its AIS then broadcasts in good faith. Either can make a ship appear to leap inland, sit in an impossible place, or drop out. The guide to position accuracy covers what that looks like on a track.

When it is our feed, not the ship

Sometimes the silence is ours. VesselTrack receives AIS through a data feed and a collector program that can be interrupted. If no position from any vessel has arrived for 30 minutes, the site says that the AIS feed is offline and shows every vessel where it was last heard, with the time. When that notice is up, the ship you are following has not disappeared — everything has stopped updating at once, and it will catch up when the feed returns.

How to tell which: a step-by-step check

  1. Check the feed. If the site says the AIS feed is offline, stop here: the gap is ours.
  2. Check how long it has been. On the vessel page, “Latest report” shows when the last position was received. A ship at anchor reports only every three minutes and a marker fades after an hour; a gap of an hour or two near the edge of coverage is routine.
  3. Look at where it was last heard. The map on the vessel page shows the last position and the recent track. Heading out to sea at speed means out of range is almost certain. Alongside a berth means it may simply be powered down.
  4. Look at its neighbours. Open the live map around that last position. If other vessels there are still being heard — bright markers, positions minutes old — the area is covered and this ship has stopped transmitting or left. If everything nearby is faded, it is the coverage.
  5. Read its declared voyage. The vessel page shows the destination and ETA the crew entered. A ship bound across an ocean will be silent for most of the passage; open the destination’s port page and watch its expected arrivals, and its arrivals and departures, around the ETA (see reading a port page).
  6. Search by IMO number. If the ship should be in a covered area and is not, look her up by IMO number in case she now broadcasts under a different MMSI.
  7. Let an alert watch for you. With Pro, the “gone quiet” alert tells you when we stop hearing a vessel in your fleet, and the arrival alert when she reports herself in port.
What you seeMost likely
Every vessel on the map faded, and a notice that the feed is offlineWait for the feed to return; nothing about the ship has changedOur feed has stopped, not the ship
Last heard heading out to sea at speedWork out from its destination and ETA when it should next be near a coastOut of range of shore receivers
Last heard near a coast, with other ships nearby also fadedLook at the map around its last position over the next hoursNo receiver covering that stretch, or a receiver outage
Last heard near a coast, other ships nearby still freshCheck whether it was moored; watch for it reappearingIts transponder stopped: switched off, powered down or faulty
The ship is clearly sailing, but its page has gone quietSearch by its IMO numberIt now broadcasts under a different MMSI
Positions that jump between distant placesLook at the track; compare the name and type with what you expectTwo transponders sharing one MMSI, or false positions

If you need to find a ship that has not been heard for a long time, the guide to finding a ship lists every way in.

Sources

Statements about AIS and maritime standards on this page were checked against the following. Statements about what VesselTrack does describe the software as it runs today.

Found a mistake? Email support@vesseltrack.net or see how to contact us. Corrections are made on this page and the review date is updated.